Material guide

Fiberglass bathtub refinishing in Evansville

Fiberglass and acrylic tubs and tub-showers wear differently from cast iron. Here is when a refinish makes sense, and when support or cracks have to be fixed first.

Why fiberglass wears the way it does

A fiberglass tub is a shell of glass-fiber reinforced resin with a thin, colored gelcoat on the surface. When it is new, the gelcoat is smooth and glossy. Years of cleaning, especially with abrasive powders, wear it thin. Eventually the surface turns dull, rough, and chalky, and stains soak in. Refinishing can restore a smooth, cleanable surface when the shell itself is sound.

Compare materials in our acrylic vs porcelain guide, and see chip and crack repair.

Common fiberglass problems

ProblemWhat it looks likeRefinishable?
Worn gelcoatDull, rough, chalky surface; stains that will not come outYes
Stress cracksFine spider-web cracks, often on the floorYes, if the floor is supported
Impact cracks or holesA break from a dropped objectOften yes, with repair
Flexing floorFloor moves or creaks underfootNot until support is fixed
Loose walls on a tub-showerWalls bow or move when pushedNot until reattached or repaired
Leaks belowStains on the ceiling below, soft subfloorPlumbing and floor repair first

Support is everything

Fiberglass is flexible. Many fiberglass tubs are installed with a mortar or foam bed underneath to support the floor. If that bed was skipped, has broken down, or the subfloor has weakened, the tub floor flexes every time someone stands in it. Flexing is what causes stress cracks, and it will crack any new coating too.

Before refinishing, we stand in the tub and press around the floor. If it flexes, the support needs to be fixed first. Sometimes that can be done by injecting foam or filler under the tub through an access panel or small holes; sometimes it requires a contractor. We tell you what we find.

The refinishing process for fiberglass

  1. Deep cleaning to remove soap scum, body oils, and mildew.
  2. Remove caulk.
  3. Repair cracks and holes with materials suited to fiberglass.
  4. Scuff-sand the surface so the coating bonds.
  5. Mask and ventilate to the outside.
  6. Apply a primer compatible with fiberglass, then topcoats.
  7. Optional slip-resistant texture on the floor.
  8. Re-caulk after cure.

Fiberglass in Evansville homes

One-piece fiberglass tub-showers became common in the 1970s and 1980s and are everywhere in homes, apartments, and rentals across the Evansville area, from the east side to Newburgh and the subdivisions north of the Lloyd. Many are still solid but look tired. Landlords near USI and the University of Evansville often refinish them between tenants.

Cost

Fiberglass tub refinishing cost depends on the size and condition. A one-piece tub-shower with walls costs more than a tub alone. See our cost guide for what affects the cost.

Care after refinishing

  • Use non-abrasive cleaners and soft cloths. Abrasive powders are what wore out the original gelcoat.
  • Do not use suction-cup mats.
  • Avoid standing on the tub rim or edges.
  • Report any new flexing or cracking early.

For fiberglass refinishing, see our bathtub refinishing services in Evansville. We serve Newburgh, Chandler, Darmstadt, Henderson, KY and nearby. Related: shower refinishing and how long a refinish lasts.

Fiberglass versus acrylic

Fiberglass and acrylic tubs look similar but are made differently. Fiberglass has a thin gelcoat over the fiber layer; once the gelcoat wears through, the surface becomes porous. Acrylic is a solid sheet, usually reinforced on the back, and is tougher. Both can be refinished, but fiberglass with worn-through gelcoat often needs more prep and repair.

Stains that will not come out

Worn fiberglass absorbs stains from hair dye, rust in water, and body oils. Bleach and abrasive cleaners make it worse by wearing the surface further. Refinishing seals the porous surface under a new coating, so it cleans easily again.

Mobile and manufactured homes

Manufactured homes around the Evansville area often have fiberglass or plastic tubs. They can be refinished when the floor is well supported. In some manufactured homes, tubs sit on minimal support, so the flex test is especially important.

One-piece tub-showers in rentals

One-piece units are common in rental properties. Refinishing between tenants restores appearance quickly. Landlords should check for flexing, cracks around the drain, and loose walls at each turnover, and fix support issues before refinishing.

Fiberglass shower stalls

Stand-alone fiberglass shower stalls are refinished the same way as tubs. The pan, where people stand, takes the most wear and is the most likely to flex and crack. Check the pan for movement and cracks around the drain before booking. A slip-resistant texture is a popular addition on shower pans.

Small cracks near the drain

Cracks often start around the drain in fiberglass tubs because the floor flexes most there. Repairing them requires opening the crack slightly, filling with a material suited to fiberglass, sanding flush, and then coating. Fix the support first or the crack will return.

Fiberglass tub questions

Can a fiberglass bathtub be refinished?

Yes, when the shell is sound and the floor is well supported. Worn gelcoat, stains, and many cracks can be repaired and refinished.

Why does my fiberglass tub floor crack?

Usually because it flexes. If the support underneath has failed or was never installed properly, the floor moves and cracks.

Can a flexing fiberglass tub be fixed?

Sometimes, by adding support underneath. If the subfloor is damaged, a contractor may need to repair it first.

What affects the cost of fiberglass tub refinishing in Evansville?

It depends on size and condition. Tub-showers with walls cost more. We give a free estimate after seeing photos or the tub.

Can a stained fiberglass tub be cleaned instead of refinished?

Light stains may clean up with mild products. Once the gelcoat has worn through, stains soak in, and refinishing seals the surface so it cleans easily again.

Can tubs in manufactured homes be refinished?

Often yes, when the floor is well supported. A flex test is especially important in manufactured homes.

Can a fiberglass shower stall be refinished?

Yes, when the pan is solid and not flexing. Cracks around the drain should be repaired first.

What cleaner should I use on refinished fiberglass?

Mild, non-abrasive products such as dish soap and water. Abrasive powders are what wore out the original gelcoat.

Why do fiberglass tubs crack near the drain?

The floor usually flexes most around the drain. Fixing the support underneath is the key to a lasting repair.

Is a fiberglass tub worth refinishing or should I replace it?

If the shell is sound and well supported, refinishing is usually far cheaper. If it is cracked and the floor underneath is damaged, replacement may be better.

Ready to refinish your tub?

Our bathtub refinishing in Evansville, IN page explains how a refinish is done, which tubs and surfaces qualify, how long it takes to cure and how to request a Free Estimate.

Related guides

When you’re ready

Request a quote

Mention fiberglass or acrylic and share a few photos — we’ll follow up with a Free Estimate.

Request a quote

Or call (812) 649-1588

Evansville Bathtub Refinishing Call (812) 649-1588