What we offer

Bathtub Refinishing Services in Evansville, IN

Full tub refinishing, chip and rust repair, shower and tile surround refinishing, and straight answers about when replacement is the better choice, for homes across southwest Indiana and Henderson, KY.

Full bathtub refinishing

Surface renewal for sound acrylic or porcelain/steel tubs with proper prep and cure guidance.

Chip & rust repair

Spot repairs that set up a lasting finish when damage is still surface-level.

Shower refinishing

Select surrounds and pans when the substrate is solid and dry.

Remodel-alternative consult

We’ll help you compare refinish vs replacement before you commit.

Full bathtub refinishing

A full refinish gives a sound tub a new, uniform surface. It is the right service when the tub is dull, stained, worn through around the drain, scattered with small chips or an outdated color. The work starts with a deep cleaning to remove soap scum, body oils, mineral deposits and any old cleaning-product residue. Old caulk is cut out. The surface is then etched or abraded so the new coating can bond, and every chip and rust spot is repaired. The area is masked and ventilated, a bonding primer is applied, and several thin coats of topcoat are sprayed on. Once the coating has cured, the tub is re-caulked.

Most of the quality of a refinish comes from the prep. A good coating sprayed over a contaminated or poorly prepared surface will peel. That’s why we ask about your cleaning products, previous repairs and any DIY coatings before we start; each one changes the prep.

Tub materials and what each needs

Cast iron

Cast iron tubs, common in Evansville’s older homes, have a thick porcelain enamel over heavy iron. They are excellent candidates for refinishing because the iron is rigid and rarely fails. Worn enamel is etched or abraded, chips are filled, and the new coating bonds well to the hard surface. Replacing a built-in cast iron tub is a major job, so refinishing often saves the most money here. See our cast iron refinishing guide.

Enameled steel

Steel tubs are lighter and thinner. Chips let water reach the steel, which rusts and spreads under the enamel. Small rust spots can be ground out, treated and filled. If rust has gone through the steel, the tub needs replacing.

Fiberglass and acrylic

Fiberglass tubs and showers have a thin gelcoat that wears through to the glass fibers, leaving a chalky, porous surface. Acrylic is tougher but scratches and dulls. Both can be repaired and refinished if they are well supported. A tub floor that flexes underfoot will crack again, so support has to be fixed first. Our fiberglass refinishing guide covers this in more detail.

Chip and rust repair

If the rest of the tub looks good, a spot repair can fix a single chip or small rust spot. Rust is removed down to clean metal, treated and filled with a hard filler, then sanded flush and colored to blend. Spot repairs cost less than a full refinish, but the repaired area may not match the old enamel’s color and gloss exactly, especially on older or colored tubs. When a tub has several chips and worn areas, a full refinish usually looks better. More in our chip and rust repair guide.

Shower, tile and surround refinishing

Tile walls around a tub can be refinished when the tile is firmly attached and the wall behind it is dry and solid. Grout lines are cleaned and repaired, and the tile, grout and tub are coated together for a consistent, easy-to-clean surface. Fiberglass and acrylic wall panels and shower pans can be refinished when they are firmly attached and not cracked through. Before quoting, we press and tap around the surround. Hollow tiles, soft spots, loose panels and crumbling grout mean water has gotten behind the wall, and that needs a contractor before any refinishing. See shower refinishing and tile surround refinishing.

Color changes and slip resistance

Refinishing is a common way to get rid of a pink, blue, green or gold tub from decades past. The tub is refinished in white or a standard off-white, often with the matching tile, so the bathroom looks current without demolition. Exact matches to unusual colors are harder, so tell us what you want when you ask for a quote.

Tub floors and shower pans can also get a slip-resistant texture during refinishing. It adds grip underfoot and is easier to keep clean than adhesive strips or mats. It is a good choice for older family members, young children or anyone with balance concerns.

Clawfoot, jetted and walk-in tubs

Clawfoot tubs are refinished inside like any cast iron tub, and the outside can be painted a color of your choice. Exposed drain and supply lines should be in good condition first. Jetted and whirlpool tubs can be refinished if the jet fittings can be removed or masked properly; the coating must not get into the jets. Walk-in tubs have doors with seals and gaskets that can’t be coated, so only some surfaces can be refinished. We look at your specific tub and explain what can and can’t be done. See our guides to clawfoot tubs and walk-in tubs.

Cure time and planning

After the coating is sprayed, it must cure before the tub gets wet. The time depends on the product, temperature and humidity; many coatings need roughly a day or more before light use, and they keep hardening for several days after that. Follow the specific cure time you are given. If you have only one tub or shower, arrange somewhere else to bathe during that time. Our cure time guide has more detail.

Safety and ventilation

Refinishing products give off strong fumes. A professional uses fans to pull air out of the bathroom and to the outside, and wears a respirator during application. Keep people and pets out of the area while the coating is sprayed and for as long as you are advised afterward. The U.S. Environmental Protection Agency has banned most uses of methylene chloride, a paint stripper linked to the deaths of bathtub refinishers who worked in small, poorly ventilated bathrooms. Ask any refinisher which strippers and coatings they use and how they ventilate.

Some older tubs have glazes that contain lead, and sanding them creates dust. Ask how prep dust is controlled and cleaned up, especially in homes with young children.

What we don’t do

We refinish surfaces. We don’t fix leaking drains, replace valves, repair floors or rebuild walls. If we find those problems, we tell you, so you can call a plumber or contractor first. We also won’t coat over a tub that is rusted through or cracked and flexing, because the finish would fail and the underlying problem would get worse.

How to get a quote

Send photos of the whole tub, close-ups of chips, rust or cracks, and the surround if you want it included. Tell us the tub material if you know it, your town and when you would like the work done. We reply with a quote and any questions. Price depends on the tub, the amount of repair, whether walls or tile are included and the drive. Read our cost guide for the factors that move the price.

Caring for a refinished tub

A refinished surface is durable, but it is not the same as factory enamel. Clean it with mild, non-abrasive products and a soft cloth or sponge. Avoid scouring powders, steel wool, abrasive pads, drain cleaners spilled on the surface and harsh acid or bleach-heavy cleaners. Don’t use suction-cup mats; they trap water and can pull at the coating. Wipe the tub after use if your water leaves mineral spots, and fix dripping faucets quickly. Run the exhaust fan during and after showers to keep moisture down. If a chip appears, have it repaired before water gets under the coating. With that care, a refinish commonly lasts around 10 to 15 years. Our guide to how long a refinish lasts covers this in more detail.

Why DIY kits often peel

Hardware-store tub kits are cheaper, but they often peel within months. The usual reasons are poor cleaning and etching, coatings brushed or rolled on too thick, too little cure time, and humidity in the bathroom during application. Once a DIY coating starts peeling, it has to be stripped before a professional refinish can bond. If you are thinking about a kit, read our DIY vs professional guide first.

Who calls us

Most calls come from a few situations: homeowners getting a house ready to sell, landlords between tenants, families who inherited a dated bathroom and want it to look clean without a remodel, owners of older homes who want to keep an original cast iron or clawfoot tub, and people whose DIY kit peeled. In each case we start the same way: look at the tub, ask what you want, and tell you honestly whether refinishing is the right fix.

Getting ready for the visit

Clear everything out of the tub and off its edges, including bottles, caddies, shower curtains and bath mats. Remove anything fragile from the bathroom counter and walls near the tub. Make sure the faucet doesn’t drip, because water on the surface interferes with the coating; if it does, have it fixed before the visit. Keep pets and children away from the bathroom during the work, and plan for the odor while coatings are sprayed. Open windows elsewhere in the house if you can. After the work, keep the bathroom door closed and the fan running as advised, and don’t use the tub until the cure time has passed. If anything about the finish looks wrong once it has cured, such as a rough spot, a run or an area that looks thin, tell us right away so it can be looked at while it is still fresh.

Refinishing service questions

Can you refinish a tub that was coated with a DIY kit?

Usually, yes. The failing DIY coating has to be removed first, which adds prep time. Tell us about any earlier coatings when you ask for a quote.

Will the refinished tub feel different?

A good refinish feels smooth and glossy like new. If you choose a slip-resistant floor, that area will feel slightly textured.

Do you refinish sinks?

Some sinks can be refinished, but many homeowners find replacing a sink simpler. We’ll tell you which makes more sense for yours.

How long does the work take?

Most single-tub refinishes are done in one visit, followed by cure time. Tile surrounds and multiple fixtures take longer.

Do you work in Henderson, Kentucky?

Yes. Henderson is just across the Ohio River and within our regular area. Addresses farther into Kentucky depend on the schedule, so send your ZIP and we will tell you.

When you’re ready

Request a quote

Share photos or a description — we’ll send a quote from our team.

Request a quote

Or call (812) 649-1588

Evansville Bathtub Refinishing Call (812) 649-1588